Author: Site Editor Publish Time: 2026-11-11 Origin: Site
A 3D fence panel is a welded mesh panel folded along its length into a series of V-shaped ridges. The folds do the structural work: they stiffen a light panel against wind and against a person pressing on it, and they remove the flat surface that makes a plain welded panel easy to scale. Everything else about the product, from wire diameter to coating, comes out of the same welded mesh process.
The label carries no specification of its own. Two panels sold as the same 3D type can differ in height by more than a meter, in wire by two full gauges and in fold count from two to four, and each of those differences changes what the panel will do on site. Buyers who order by label end up comparing offers for products that are not equivalent.
The name refers to the profile, not to a grade. A flat welded panel relies on wire diameter and post spacing for its rigidity; folding the same mesh into ridges adds stiffness without adding steel, because the ridge acts as a beam along the panel's length. That is why a folded panel of modest wire can outperform a heavier flat one against wind pressure.
The fold also changes how the panel behaves under attack. A flat mesh gives a climber a continuous plane for hands and feet. Ridges interrupt that plane and leave only the horizontal wires as footholds, which raises the effort required without pretending to make the fence impassable. A fold does nothing for a panel lifted at its base, which is a footing problem rather than a profile one.
Treat 3D as a family name. The specification is the set of numbers that follows it, and those numbers have to be chosen one at a time.
Fold count is not a style choice; it is set by height. Panels from 630 to 1430 mm carry two folds. From 1530 to 1930 mm the count rises to three. From 2030 to 2430 mm it reaches four. The progression exists because a taller panel needs more lateral restraint to resist wind and to stop the mesh plane from oil-canning between posts.
This matters when a project mixes heights. A boundary stepping down a slope may use three heights in one run, and each will have a different fold count and therefore a different stiffness. Post spacing that works at 1230 mm may be marginal at 2030 mm, where the panel is taller, carries an extra fold and presents more sail area.
Confirm fold count against height at order. A supplier quoting a 2430 mm panel with three folds is describing a different product.
Wire diameter does more for performance than any other single number. The range runs from 3.0 to 5.0 mm, and the difference between the ends is not cosmetic: 3.0 mm at a wide aperture is a demarcation panel, while 5.0 mm at a tight aperture is a barrier that resists a shoulder charge and takes far longer to cut.
Aperture works with wire rather than against it. The options are 50 × 100, 50 × 150, 50 × 200 and 75 × 100 mm. A 50 mm gap between verticals is too narrow for a boot or a handhold; a 200 mm gap is a ladder for anyone determined. Where the fence is a boundary against intrusion, the tighter aperture earns its cost. Where it is a sports enclosure or a demarcation line, the wider mesh lets wind through and reduces load on the posts.
Specify both numbers, never one alone.
Widths are 2000, 2500 and 2900 mm, and the choice is a site decision as much as a product one. Wider panels mean fewer posts, fewer clamps and faster installation per meter, which is why 2500 mm dominates contractor work. Narrower panels are easier to handle on a tight boundary, on a slope, or where the fence has to step around an obstruction.
Width also sets how the run handles level change. A welded panel is rigid, so a slope is stepped rather than followed, and each step needs a post. On a long gradient, narrow panels produce smaller steps and a tidier line; wide panels produce larger steps but fewer posts. Neither is wrong, but the visual result differs and clients notice it.
Set out the bay before ordering. Measure the run, divide by the chosen width, and check what the remainder does at each corner.
A panel is only as rigid as its fixing. Post options run from round 48 mm and 60 mm OD tube in 1.5 or 2.0 mm wall, through square 50, 60 and 80 mm sections, to rectangular 40 × 60, 40 × 80, 60 × 80 and 80 × 100 mm. Wall thickness separates a post that holds a tensioned line from one that leans after two seasons.
Connection type decides how load transfers. Clamp bar, I-post, J-bolt, metal clamp, peach post, square clamp and U-bolt each suit a different post section and a different level of dismantling. A clamp bar spreads load along the fold and is the usual choice for a permanent boundary. A U-bolt on a round post is quicker to fit but concentrates stress at two points.
Match connection to post, and post to wind load, before comparing panel options. On a 2900 mm panel the clamp count per bay is higher, and every clamp is a fixing that can work loose over a season.
The finish has to survive the site, and the two routes are galvanized or electrostatic powder coated in any RAL color. Galvanizing protects by sacrificial action, including at cut edges and weld intersections where coverage is thinnest. Powder coating seals the surface and supplies the color that architects and sports clients ask for, but it is a film: once breached, corrosion works beneath it and lifts the coating from behind.
The production sequence matters. Wire is straightened and cut, welded, bent, then coated, and that order determines whether fold edges and weld points receive full coverage. A panel coated before bending will show bare steel along the fold line.
For coastal or industrial sites, specify galvanizing plus powder rather than powder alone, and inspect a delivered panel at the fold. Color stability matters as much as adhesion on elevations that face the sun, because chalking is the first thing a client notices and the last thing a supplier wants to discuss.
Begin with what the fence has to do. A sports enclosure needs a clear sightline, consistent height and a finish that matches the building. A boundary needs a tight aperture, heavier wire and a post that will not move under load. A works compound needs panels that can be lifted out and reused without the coating failing at the clamps.
Then translate that into the six numbers a supplier needs: height, width, wire diameter, aperture, fold count and post section, plus connection type and finish. A 3D fence panel ordered on those lines can be compared against another offer line by line. One ordered as a green 3D panel cannot.
Ask for a drawing of the bay and the post detail. That is where a mismatch between panel width and post spacing becomes visible. Where two suppliers quote the same six numbers, the difference usually sits in the post wall and the coating, and both can be checked on a sample before the order.
Fold count follows height, aperture follows purpose, and wire diameter follows the level of resistance required. Get those three relationships right and the rest of the specification falls into place; get them wrong and no amount of coating quality will compensate.
A 3D fence panel bought on the six-line specification is a product a buyer can defend to a client. Post spacing and connection choice belong in the same conversation, because a correctly specified panel held by an undersized clamp behaves like a cheaper product on the first windy week. Anping Tailong Hardware & Wire Mesh Products Co., Ltd. produces folded welded panels in the full height and wire range and can supply bay drawings and post details against a measured run before an order is confirmed.
It describes the folded profile. The panel is welded mesh bent into V-shaped ridges running along its length, which stiffens it and interrupts the flat climbing surface. The term says nothing about wire diameter, height or coating, so it should always be followed by those figures when a panel is specified or compared.
Start with the purpose. A low panel demarcates; a taller one resists. Where the fence must deter entry, height should be set with the fold count and post spacing in view, because a taller panel carries more wind load. Confirm the combination of height, fold count and post section together rather than choosing height alone.
They can be cut, but every cut exposes bare steel and every cut edge needs repair coating or the panel will corrode from that point. Cutting also removes the fold at the end, which is where much of the panel's stiffness sits. Where a run ends short, adjust the bay layout rather than the panel.
Both keep a fifty millimeter gap between vertical wires, so neither gives a foothold. The difference is the horizontal spacing: one hundred millimeters gives a denser, heavier panel with more horizontal wires, while two hundred millimeters is lighter, lets more wind through and costs less in steel. The denser mesh suits security boundaries; the open one suits sports and demarcation.
They can be, and they should be specified in the same order. Posts and connections are chosen against the panel height, wind load and whether the fence will ever be dismantled. Buying panels from one source and fixings from another is where rigidity is usually lost, because the two are rarely matched on load.