News

Home » News » Wire Mesh Fence » Curvy Fence Supplier: 630-2430mm Panel Heights, V-Folds & Post Specs

Curvy Fence Supplier: 630-2430mm Panel Heights, V-Folds & Post Specs

Author: Site Editor     Publish Time: 2026-11-17      Origin: Site

Inquire

facebook sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button

Curvy Fence Supplier: 630-2430mm Panel Heights, V-Folds & Post Specs

A curvy fence is normally ordered as one line on a purchase list, and that habit causes most of the specification errors in this product family. Height sets the fold count, the fold count sets how the panel behaves under wind load, and that behavior decides which post section and which connection will hold the panel in service. A buyer who sends a single height and a single post size receives a quotation for one case only.

The published range is a matrix rather than a menu: thirteen heights from 630 mm to 2430 mm, three widths, five wire diameters, four mesh openings, and a post list that runs across round, square and rectangular sections. This guide treats that matrix as a set of decisions for importers, distributors and fencing contractors who need to compare offers on equal terms.

3D Curvy Fence Height Matrix: Why Steps Tighten Above 1430mm

The height list runs from 630 mm to 2430 mm in thirteen steps, and the steps are not evenly spaced. Between 630 and 1430 mm the increments are 200 mm; from 1530 mm upward they tighten to 100 mm. That change is not a catalog quirk. It coincides with the boundary where the panel gains a third fold, so the range becomes denser exactly where structural behavior starts to change quickly.

Read the list that way and it turns into a specification tool. A 1430 mm panel and a 1530 mm panel differ by a single 100 mm step, yet they sit on opposite sides of a fold-count boundary. Where a run has to read as continuous with a neighboring fence, choose the height from the site first and read the fold count off second. Doing it the other way round produces a run with a visible step in the fold lines, which is difficult to correct once the posts are set.

Longitudinal V-Fold Count: 2, 3, and 4 Folds as Structural Stiffeners

Folds run longitudinally and the count follows height: 630 to 1430 mm gives two folds, 1530 to 1930 mm gives three, and 2030 to 2430 mm gives four. Each fold is a horizontal stiffening line, so the count is the cheapest stiffness the product has. It also fixes where shadow lines fall across the panel face, which is why mismatched fold counts are visible from a distance even when the heights are close.

The practical consequence is that a 100 mm height increase can change both the panel's resistance to wind pressure and its demand on the post. A buyer comparing two offers at nominally the same height should confirm the fold count in writing. A supplier working from a different height table can deliver a panel that meets the dimension and misses the stiffness, and the difference only appears in the first strong wind.

Curvy Fence Width Modules: 2000mm, 2500mm, and 2900mm Bay Economics

Panels come in 2000, 2500 and 2900 mm widths. Width is what converts a run length into a post count, and post count is usually the largest single variable in the delivered cost of a fence line. A 2900 mm module needs fewer posts per meter than a 2000 mm module, but it also carries more sail area per span, which pushes load back into the post section.

Width also decides how the run closes. Choose a module that divides the run with the fewest cut panels, and place any cut at a corner or a terminal rather than mid-run. A cut panel loses its folded edge at the cut, so that end needs a clamp bar to hold the mesh and restore edge stiffness. Two or three cut panels in a line are normal; a line made mostly of cuts is a layout error that will show at every junction.

Wire Diameter (3.0-5.0mm) and Mesh Aperture (50x100 to 75x100mm) Selection

Wire diameter runs 3.0, 3.5, 4.0, 4.5 and 5.0 mm; mesh opening runs 50×100, 50×150, 50×200 and 75×100 mm. The two are independent, and buyers often trade one against the other by accident. Aperture is a visibility and climb-resistance decision: 50×100 mm gives the densest screen, while 50×200 mm leaves the most open face and the most porosity for wind.

Wire diameter is a stiffness and damage-tolerance decision. Moving from 3.0 to 4.0 mm changes how the panel behaves when a vehicle door touches it and how far it deflects between posts. The common mistake is to specify a tight aperture to get a secure appearance and then accept the thinnest wire to keep panel weight down. That combination delivers the look and not the resistance.

Aperture also sets what the fence does to a view. The 75×100 mm option reads as a heavier grid than 50×100 mm at the same height, which matters where a boundary sits beside a footpath.

Curvy Fence Post Profiles: Round, Square, Rectangular, Peach, and I-Posts

Round posts are 48 mm and 60 mm outside diameter; square posts are 50, 60 and 80 mm; rectangular posts are 40×60, 40×80, 60×80 and 80×100 mm. Wall thickness is offered at 1.5 and 2.0 mm across the range, so section size rather than wall does most of the work. Increasing section raises stiffness far more than adding wall to a small section.

Shape follows function. Square posts take clamps on flat faces and give a clean line; round posts suit curved runs and accept a wider range of clamp angles; rectangular posts are directional, so orient the long axis into the prevailing wind. For a tall panel on an exposed site, the post is where the specification should be raised first, because it is the component that is expensive to change after the footings have cured. Wall thickness matters most at the base, where bending stress peaks as the post enters the ground.

Panel-to-Post Connections: Clamp Bars, Metal Clamps, Peach Clips & U-Bolts

The range covers clamp bar, I-post, J-bolt, metal clamp, peach post, square clamp and U-bolt. The choice follows the post and the maintenance plan rather than the panel. A clamp bar with a cover hides the fastener and is the right default for a boundary where the panel should not be removable from outside.

Bolted connections such as J-bolt and U-bolt allow adjustment and re-tensioning after installation, which matters on long runs where posts settle. If one bay must be lifted out for vehicle access, make that bay demountable and keep the rest fixed. Specifying every bay as demountable adds hardware and gives away the security the fence was bought for, so the decision belongs at the layout stage rather than on the order.

Peach post and I-post connections reduce visible hardware on the face of the fence, but they are less forgiving of a post that is out of line.

Building a Standardized Curvy Fence Procurement Schedule for Importers

Six quotations for a curvy fence are rarely comparable, because each supplier fills the gaps in a short enquiry with its own defaults. The remedy is a one-page schedule with a row per panel type and a column for each variable: height, fold count, width, wire diameter, aperture, post section and wall, connection, finish, and accessories.

Finish belongs in the schedule because the range allows galvanized or electrostatic powder coated in all RAL colors, and a color match between gate, panel and post is a separate line to confirm. Accessories such as barbed wire or razor wire change the top detail and often the post height as well. Where a value is not published, ask for it to be stated on the quotation rather than assumed from a previous project.

Two lines are routinely forgotten and both cause site delays: the post cap, either a metal rain cap or an anti-UV plastic cap, and the fixing pack, which has to suit the post section chosen.

Conclusion

A curvy fence order succeeds or fails on the matrix, not on the panel alone. Fix the height from the site, read the fold count from the height, then size the post and choose the connection so the assembly can carry the load and still be serviced. Get that sequence right and the quotation becomes a specification rather than an opening offer. The matrix is short enough to be answered in writing, which makes it a practical test of any supplier.

Anping Tailong Hardware & Wire Mesh Products Co., Ltd. has produced wire mesh since 1989 and builds these panels on automated lines with in-house welding, offering CAD and 3D MAX renderings so a buyer can check fold alignment and post positions before a drawing is released. Send the schedule, not a single line item.

Frequently Asked Questions

Q1. Does the V-fold count change automatically with curvy fence panel height?

Yes, the fold mapping follows panel height automatically across the thirteen standard heights: panels from 630 millimeters to 1430 millimeters feature two horizontal folds, panels from 1530 millimeters to 1930 millimeters feature three folds, and panels from 2030 millimeters to 2430 millimeters feature four folds.

Q2. Can a curvy fence panel be cut to a shorter width on site?

Yes, a panel can be trimmed horizontally at a corner or gate closing bay, though cutting removes the factory end wire. Securing the cut panel edge inside a full-length steel clamp bar or I-post channel restores edge rigidity and conceals the cut wire ends after zinc touch-up.

Q3. Which post section should be specified for tall 2030 to 2430 millimeter panels?

Tall four-fold panels carry higher wind loads and should be paired with 60 millimeter round posts, 60 by 60 or 80 by 80 millimeter square posts, or 60 by 80 and 80 by 100 millimeter rectangular posts with a 2.0 millimeter wall thickness for maximum bending resistance.

Q4. What anti-corrosion coatings and color options are available for curvy fencing?

Panels and posts are available in full hot-dip galvanized finishes conforming to International Organization for Standardization 1461 or galvanized steel topped with electrostatic polyester powder coating across all standard color chart shades, including moss green, anthracite gray, jet black, and custom corporate colors.

Q5. How do the 2000, 2500, and 2900 millimeter panel widths compare in cost?

The 2500 millimeter width is the most widely stocked container module, while the 2900 millimeter width reduces total post holes and footing concrete by nearly fifteen percent on long straight runs. The 2000 millimeter width is preferred on sloped ground or high-wind coastal perimeters.

Contact Us Now

  Tel:
+86-318-7813366
Mobile: 
+86-153-6985-6999
+86-133-2318-6988
WhatsApp: 
+86-15369856999
No.19, Jingsi road, high-tech-industrial
development zone, anping country hebei province, China

Quick Links

Products

Get A Free Quote

Contact us
Copyright © 2025 Tailong. All Rights Reserved.   Sitemap