Author: Site Editor Publish Time: 2026-11-19 Origin: Site
Cattle fence panels often look identical on a basic price sheet, yet a rotational pasture pen, a commercial dairy holding yard, and a high-throughput beef feedlot or saleyard subject steel rails to completely different forces. A 1.8 meter panel that performs for decades along a quiet dairy lane can bow in a single afternoon if installed at the crowding corner of a bull pen or saleyard forcing chute.
To match structural steel mass to actual animal pressure without overspending on low-load zones, we manufacture hot-dip galvanized cattle fence panels across three standardized load-bearing grades—Bronco, Pasture Heavy-Duty (PHD), and Super Heavy-Duty (SHD)—in 1.8 meter heights, 2.07, 2.1, 2.4, and 2.9 meter widths, and 5-rail or 6-rail configurations using oval (30 by 60, 40 by 80, and 42 by 115 millimeter), square (40 by 40 and 50 by 50 millimeter), and round (32, 42, and 60 millimeter) steel tubing.
Livestock containment loads fall into three distinct mechanical categories. In pasture holding pens and dairy loafing yards, cattle apply intermittent rubbing and leaning pressure. In rotational sorting pens and farm working races, crowded mobs apply cyclic lateral pushing. In commercial feedlots, bull pens, and auction saleyards, heavy cattle slam into rails and joints at speed.
Our Bronco grade panel is engineered for everyday pasture containment, portable holding pens, and calm dairy flow lanes where easy manual handling and economical container loading matter most. Stepping up to the Pasture Heavy-Duty (PHD) grade increases rail section and wall thickness for active sorting yards, weaning pens, and all-purpose ranch corrals.
At the top of the range, Super Heavy-Duty (SHD) cattle fence panels use maximum-section rails and heavy-wall vertical posts designed specifically for high-density feedlots, crowding tubs, crush approaches, and public saleyards where zero rail deflection is permissible.
Oval steel tubing is the preferred rail geometry across modern Australian, New Zealand, and North American cattle yards because it places the long axis of the ellipse against horizontal bending while presenting a broad, smooth, flat face toward the animal's shoulder and ribcage.
We fabricate oval-rail cattle fence panels in three graduated rail sections: 30 by 60 millimeters for Bronco and standard farm yards, 40 by 80 millimeters for PHD working corrals and races, and massive 42 by 115 millimeters cattle rails for SHD feedlots and bull yards.
Because the wide face of a 40 by 80 millimeter or 42 by 115 millimeter oval rail eliminates sharp corner edges, cattle moving rapidly through a narrow race or crowding pen suffer significantly less hide damage and carcass bruising prior to market.
Depending on regional ranching standards and existing yard compatibility, buyers also specify square-rail or round-rail cattle fence panels. Our square-rail lineup uses 40 by 40 millimeter or 50 by 50 millimeter horizontal rails welded to matching 40 by 40 or 50 by 50 millimeter vertical posts, offering high torsional stiffness and full four-sided weld seams.
For ranchers and contractors who prefer traditional tubular pipe corrals, our round-rail cattle panels are built from 32 millimeter, 42 millimeter, or heavy 60 millimeter outside diameter steel pipes that shed mud and manure effortlessly.
Across all three rail geometries—oval, square, and round—panels are manufactured to a standard 1.8 meter height and widths of 2.07, 2.1, 2.4, and 2.9 meters, ensuring full interchangeability across mixed-grade yard expansions.
Holding a uniform 1.8 meter panel height across an entire livestock facility keeps top rails, gate frames, and overhead braces level while allowing you to vary between 5-rail and 6-rail configurations by zone. Height discourages jumping; rail count controls head reach and lower-panel stiffness.
Six-rail cattle fence panels tighten the clear vertical gaps in the bottom and middle thirds of the 1.8 meter frame, preventing calves, yearlings, or horned cattle from pushing heads through the fence line in high-density feedlots, weaning pens, and forcing yards.
Five-rail panels provide a lighter, more open structure ideal for dairy cow flow lanes, dry-cow holding areas, and outer perimeter runs where mature cattle walk familiar routes twice daily and operators occasionally lift panels for wash-down access.
In saleyards and crowding pens, structural failure almost always occurs at the panel-to-panel connection rather than the middle of a rail span. A single thin hook or loose chain connector twists open when a 700-kilogram steer hits the joint at an angle.
Every cattle fence panel in our range is built around 40 by 40 millimeter or 50 by 50 millimeter vertical end posts fitted with heavy-duty 50 by 50 millimeter welded U-lugs or L-lugs and two full-length steel drop pins per joint. Using two drop pins per vertical post locks adjacent panels against both horizontal shear and vertical lifting.
Each vertical post is sealed at the top with a welded steel rain cap to block internal water accumulation, and finished at the bottom with a welded steel foot base pre-drilled for concrete bolting or ground staking.
A cattle yard only operates as fast as its transitions into the veterinary crush and the transport loading ramp. Because a cattle crush and an adjustable loading ramp occupy fixed footprints, the surrounding SHD and PHD cattle fence panels must pin directly to their entry and exit frames without leaving shoulder-trapping gaps.
We manufacture matching single swing, double swing, and sliding cattle yard gates—including slam-latch race gates and man-escape gates—built inside heavy rectangular portal frames that share the exact same 1.8 meter height and twin drop-pin lug spacing as our Bronco, PHD, and SHD panels.
Placing slam-latch drafting gates at the exit of the crush and heavy-duty 42 by 115 millimeter oval-rail SHD panels along the forcing chute ensures neither operators nor livestock encounter a weak link.
Importers and livestock equipment dealers can maximize forty-foot container value by combining Bronco, PHD, and SHD cattle fence panels into one coordinated bill of materials. Because all three grades share the 1.8 meter height, 2.07 to 2.9 meter module widths, and twin drop-pin lug geometry, they pin together cleanly on any ranch.
Specify SHD 6-rail panels with 42 by 115 millimeter or 40 by 80 millimeter oval rails for the crush approach, forcing pen, and loading ramp mouth; PHD 6-rail panels for sorting alleys; and Bronco 5-rail panels for outer holding pens.
Confirming hot-dip galvanizing thickness (ISO 1461) or heavy pre-galvanized zinc mass plus zinc-rich weld coating on the factory approval drawing guarantees multi-decade corrosion resistance in wet feedlot manure.
Matching cattle fence panels to actual yard loads across Bronco, Pasture Heavy-Duty (PHD), and Super Heavy-Duty (SHD) grades prevents overbuilding in calm lanes and structural failure in high-pressure pens. Combining 1.8 meter heights, 2.07 to 2.9 meter widths, 5 or 6 rails in 30 by 60, 40 by 80, or 42 by 115 millimeter oval, square, or round profiles, and twin drop-pin lugs creates a rock-solid yard.
Anping Tailong Hardware & Wire Mesh Products Co., Ltd. manufactures Bronco, PHD, and SHD cattle fence panels, heavy-duty cattle feeders, crushes, and loading ramps from one integrated production base. Send us your yard layout or container schedule for CAD drawings and factory-direct pricing.
Bronco panels use lighter 30 by 60 millimeter oval or 32 millimeter round rails for calm pasture holding pens and easy portability. Pasture Heavy-Duty panels step up to 40 by 80 millimeter oval or 42 millimeter round rails for active working corrals, while Super Heavy-Duty panels use 42 by 115 millimeter oval or 60 millimeter round rails for feedlots and saleyards.
Our standard cattle fence panel height is 1.8 meters, which effectively prevents beef and dairy cattle from jumping out of pens while keeping stock clearly visible to yard handlers. Standard modular panel widths include 2.07 meters, 2.1 meters, 2.4 meters, and 2.9 meters across both five-rail and six-rail configurations.
Oval rails in 30 by 60, 40 by 80, and 42 by 115 millimeter profiles present a broad, flat, corner-free surface toward moving cattle. This smooth geometry prevents hip and shoulder bruising when animals crowd tightly into a forcing pen or single-file veterinary race.
Each vertical 40 by 40 or 50 by 50 millimeter post is fitted with welded steel U-lugs or L-lugs that accept two separate heavy-duty steel drop pins per connection. Using two pins prevents adjacent panels from twisting, lifting, or hinging apart under sudden animal impact.
Every vertical post on our cattle fence panels is sealed at the top with a welded steel rain cap so water cannot enter the hollow tube, and finished at the bottom with a welded steel foot base that keeps the lower rail off wet mud and accepts anchor bolts.